擠塑板安裝的時候要保證表面的清潔，并且不能有雜物的出現，要不然就粘貼的不牢靠了，今天沈陽擠塑板的老師傅就給大家講解一下。

    施工時，用膩子刮板將配置好的膠料刮抹于擠塑板表面，厚度為1mm，用力要均勻，使膠料均勻分布在擠塑板的表面。擠塑板間的縫隙宜小于等于3㎜，嵌入縫隙內的水泥漿清除深度大于等于10㎜，擠塑板間的縫隙用NP中性硅酮密封膠或JS擠塑板界面劑嵌填飽滿。外墻面局部損傷的擠塑板，應將其輪廓裁切成矩形，用周圈抹JS界面劑相應形狀的擠塑板嵌填補齊。輔助模板拆除后，對外漏的擠塑板應及時刮抹界面劑。

    內模就位將外墻內側模板按預定位置就位，用常規方法合模即可。擠塑保溫板豎排至門、窗口時，可根據需要橫綁在外墻面上，使其不出現細窄拼條。

    擠塑板在外模上口樓板厚度范圍內要放L型鍍鋅鐵皮，其作用是保護保溫板上口，又使墻體澆筑時混凝土不會填入樓板段擠塑板的燕尾槽內。內外模板拆除后，支完樓板模板和綁完鋼筋，利用外墻穿孔螺栓，安裝外墻輔助模板，即由擠塑板與輔助外模共同起樓板側模的作用。澆筑樓板混凝土時，混凝土填入擠塑板的燕尾槽，樓板混凝土與擠塑板形成咬和連接，待拆除輔助模板后，整塊擠塑板就與外墻結為一體，形成了外墻的外保溫層。

    擠塑板堵孔拆模后，用擠塑板開孔器在擠塑板上裁出與螺栓孔直徑相同，且與保溫層厚度相同的圓柱體，在其周圈表面涂抹JS擠塑板界面劑后，立即塞入穿墻螺栓在擠塑板上留下的孔內。

    完成以上的所有步驟之后擠塑板的安裝就搞定了，詳細的步驟就這樣的介紹完成了。

    轉載本文請注明：沈陽擠塑板//wxsoftware.cn/